Products - Saftey engineering

Manual fire alarm [Type C31]

The C31 can be used outside and in moist spaces as a surface mount. The highly flame resistant plastic casing is UV resistant. The easily replaceable glass panels consist of colourless thin sheet glass. The alarm button is locked as soon as it is pressed, and can only be reset using the covered reset lever. The C31 is available in the standard colours red, yellow or blue. By request we will also deliver this manual fire alarm in other colours

more ...


Manual fire alarm [Type dC31]

The detector, type dC31, was developed for explosion hazard areas, where gas or dust can cause an explosive atmosphere. The device provides a maximum security, without using a safety barrier. According to a free choice of different resistors, at a threshold alarm system, the detector can be used at several fire alarm systems. The impact resistant chassis is available on stock in five different colours. The easily replaceable glass panel consist of flat, colourless thin sheet glass.

more ...


Flashing warning lamp [Type BWL]

The optical BWL signal is built into a waterproof and weatherproof (IP 66) casing intended for wall mounting. The transparent spherical cover comes standard in green. Yellow, orange, red or clear are also available. The red body consists of thermoplastic ABS. The BWL is available in a variety of supply voltages: 230 VAC and 12 and/or 24 VDC. The tubes flash with approx. 5 watts per second. The frequency can be adjusted

more ...


Emergency switch with glass panel [Type C65/G]

The waterproof C65/G emergency switch was developed based on the IP 66 protection standard. It is particularly well suited for publicly accessible areas, since the switch is protected against unintentional activation by a replaceable glass panel. The C65/G possesses a durable, thick-walled and shock-proof plastic casing. The emergency switch is also outfitted with a tall cylindrical shroud.

more ...


Emergency switch with glass panel [Type dC65/G]

The switch and button casing of the dC65/G are made of robust, shock-proof and antistatic plastic. The button is protected against unintended activation by a glass panel. We deliver the switch to you with ATEX- approved cable fasteners. We also will install resistor modules asrequested for line monitoring

more ...


Holding solenoid [Type eD1475]

The eD1475 serves to seize fire and smoke protection doors. The gray cast casings protect the device against overheating by conducting away the warmth developed by the holding solenoid. The weatherproofencapsulation also fulfils the IP 66 standard for Ex protection. The eD1475 is rated for 24 volt DC voltage. The standard version works with 3 watts - custom variations can also be created with higher capacities. The holding solenoid come in two versions: 50 and 70 mm in diameter. Anchor plates in various sizes are also optionally available.

more ...


Pressure Switch [Type C72/C]

The intrinsically safe C72/C pressure switch monitors the pressure from fluids and gases in explosive environments. To that end the upper and lower switching points can be separately adjusted. The inner threads of the pipe connection measures G 3/8».

more ...


Lighted panel [Type LT370]

The weatherproof LT370 warns employees about the danger status of special areas. The panel is equipped with a fluorescent lamp. A transparent spherical bed is positioned within the polycarbonate casing with yellow, replaceable text transparencies. The casing is protected based on IP 65.

more ...


Lighted display [Type 6100/108]

The 6100/108 lighted display contains two fluorescent lamps. The casing consists of a glass fibre reinforced polyester resin and a transparent, orange-toned spherical tray with a prism structure. The 6100/108 is suitable for wall mounting in explosive areas.

more ...


Switch and button [Type dC65]

The casing of the dC65 consists of robust, shock-proof and conductive plastic and is suitable for wall mounting in explosive areas. We deliver the switch to you with ATEX-approved cable gland. We will also install resistor modules as requested for line monitoring.

more ...


Connection box [Type eD65]

The eD65 connection box is explosion-proof and additionally corresponds to the IP 66 protection standard. Various terminals can be installed into the antistatic plastic casing. We deliver this socket to you with up to six ATEX-approved cable gland. Resistor modules for line monitoring can also be installed by request.

more ...


back to previous page